RFID-Schloss Niro.RFID – Das vielseitige, elektronische Schrankschloss für moderne Anwendungen

Das Niro.RFID von BURG ist ein innovatives, elektronisches Möbelschloss, das speziell für den Einsatz in Büros, Fitnessstudios, Wellnessanlagen und öffentlichen Gebäuden entwickelt wurde. Es bietet eine kabellose, schlüssellose Lösung für Schränke, Spinde, Schließfächer und Briefkästen. Dank der robusten Metallkonstruktion und der ergonomischen Touch-Bedienung gewährleistet das Schloss sowohl Sicherheit als auch Benutzerfreundlichkeit.

Produktfeatures

  • Modernes Design: Das Schloss ist in einem eleganten Schwarz gehalten und passt sich perfekt in jede Umgebung ein.
  • Langlebig und wertig: Die robuste Metallkonstruktion sorgt für eine hohe Lebensdauer, ideal für den intensiven Gebrauch in öffentlichen Einrichtungen.
  • Schnelle und sichere Bedienung: Dank des ergonomischen Zahlencodes und der Touch-Bedienung können Benutzer das Schloss schnell und sicher bedienen.
  • Flexibel einsetzbar: Das Niro.RFID ist für Schränke, Spinde, Schließfächer und Briefkästen geeignet und kann sowohl im Privat- als auch im Multi-User-Modus betrieben werden.
  • Kabellos und batteriebetrieben: Das Schloss wird mit einer langlebigen Batteriezelle betrieben, die den kabellosen Betrieb über eine lange Zeit gewährleistet.

Montage und Bedienung

Die Installation des Niro.RFID ist einfach und erfolgt über die Standardlochung, die für Schränke und Spinde verwendet wird. Das Schloss kann ohne zusätzlichen Verkabelungsaufwand montiert werden. Nach der Installation erfolgt die Bedienung über eine benutzerfreundliche Touch-Oberfläche, bei der der Zugang über einen 4- oder 6-stelligen Zahlencode gesichert wird. Der Multi-User-Modus ermöglicht die Nutzung durch mehrere Personen, während im Privat-Modus ein individueller Pin Code verwendet werden kann.

FAQ

1. Wie lange hält die Batterie im Niro.RFID?
Die Batterie des Niro.RFID hält je nach Nutzung circa 24 Monate und kann einfach ausgetauscht werden.
2. Kann das Schloss auch für Metall- und Holzschränke verwendet werden?
Ja, das Niro.RFID ist für Schränke aus Metall und Holz gleichermaßen geeignet.
3. Ist das Schloss wasserfest?
Das Niro.RFID ist spritzwassergeschützt, wodurch es ideal für den Einsatz in Umkleiden und Wellnessanlagen geeignet ist.
4. Wie viele Benutzer können das Schloss im Multi-User-Modus verwenden?
Im Multi-User-Modus können unbegrenzt viele Benutzer das Schloss verwenden, solange sie den korrekten Pin Code eingeben.
5. Was passiert, wenn der Zahlencode vergessen wird?
Wenn der Zahlencode vergessen wird, kann das Schloss mit einem Master-Pin-Code zurückgesetzt werden, um den Zugang wiederherzustellen.

Lieferumfang

  • 1x Niro.RFID Möbelschloss
  • 3x Riegel Typ B
  • 1x RFID-Transponderkarte
  • 1x M19 Mutter
  • 1x Gummidichtung
  • 1x Bedienungsanleitung

Hinweis: Masterkey ist nicht im Lieferumfang enthalten!
Videos
technical specifications "Niro.RFID"
Battery: 2x AAA
Battery life (locking cycles): ca. 50.000
Bolt-type: B
Bolt fastening: Screw
Colour: Black
DIN-Stop: rechts & links
Emergency power supply: no
Frequency: 13,56 MHz
Lock fastening: M19-screw-nut
Locking angle: 90° links, 90° right
Locking movement: left and right
Master-Key function: yes
Material: Zamak / Stahl
Material thickness: 22mm
Modes: Multiuser-mode with occupation display, Private-mode
Mounting hole (mm): 16 x 19
RFID-Standard: MIFARE® Classic 1K, MIFARE® Desfire EV
Surface: pulverbeschichtet
Temperature application range: -10 bis 50 °C
RFID Transponder card
RFID transponder card MIFARE® Classic 1K 13.56 MHz redThe red transponder card can be used as a convenient key replacement for our RFID locks in wooden furniture. It communicates on the 13.56 MHz MIFARE® Classic 1K standard. The lock can be opened and closed simply by holding it in front of the lock.Which locks is this transponder card compatible with?Intro.RFID W-EIR-01Flexo.RFID W-FRR-01Master Pro W-EMS-02TwinPad W-TWP-01 Scope of delivery1x transponder card red

€7.99*
Transponder enabling box Mifare (13.56 Mhz)
Transponder Release Box Mifare Classic (13.56 MHz)The transponder release box allows for the manual removal of an occupancy detection on a Mifare medium such as cards, wristbands, or chips. It is commonly used in sports facilities, offices, and fitness studios, where staff at the counter remove the occupancy detection from the media of visitors who have accidentally locked their compartment after leaving the changing room. The box features a high-quality plastic housing, is wireless, and operates with two CR123A batteries. With its compact dimensions of only 61 x 61mm, it fits elegantly into any counter landscape and is an ideal complement to BURG's electronic transponder locking systems. Advantages Easy deletion of occupancy detections Transponders are reusable after release Immediately usable without programming Suitable for Flexo.RFID, Master Pro, Corona II, Corona I FW V3.0 Deletes only block 0 of the respective sector: time recording / check-in and occupancy detection Note: If the information to be deleted is located in a sector other than 0, a specific sector card is required to correctly configure the release box. Scope of Delivery Transponder release boxNote: Batteries are not included. One CR123A battery is required.

€196.49*
Type-B bolt (rod acceptance)
Type-B bolt with rod acceptance for BURG handle, lever, bolt, and furniture locksWith this latch, various locks with the catch receptacle for the BURG Latch Type B can also be retrofitted to a two-point locking system using rods.InstallationThe latch, along with the tension spring, is placed onto the suitable catch receptacle on the lock and secured with a nut or screw. Now, the rods can be placed onto the rivet tips and secured against dislodging by turning the tension spring.Included in delivery1x Latch Type B1x Tension Spring

€2.49*
Locking angle SW1 8mm
Locking angle SW1 The locking bracket is an optimal accessory for wooden furniture cam locks, screw-on locks and espagnolette locks. The material is steel and the surface is nickel-plated. How is it mounted?The striking plate is screwed to the wood with 2 wood screws at a 90 degree angle. The mounting bracket is easy to fit and ensures a secure hold for the transom.Scope of delivery:1x Locking angle SW1 8mm

€2.49*
%
Angled locking plate 8mm
Angled locking plate 8mmCounterpart for cam locks, can be used for locking lockers, compartments and cabinets. Suitable for lever, furniture, code and locker locks. The locking plate is made of steel and the surface is nickel plated. The plate offers a surface of 8mm with which the bolt is held. Further dimensions can be found in the gallery.How is it mounted? The locking plate is fixed with 2 wood screws at the height of the locking bolt at a 90 degree angle in the inside of the wooden furniture.Delivery content1x locking plate WIN-FALLENS 8mmNote: This is a discontinued item and can no longer be ordered once stock has been used up.

€0.99* €2.73* (63.74% saved)
Locking angle SW3 11mm
Locking angle SW3 Counterpart for cam locks, for locking lockers, compartments and cabinets. Suitable for use with lever, furniture, code and sash locks. The striking plate is made of steel and the surface is nickel-plated.The angle with which the bolt is held provides a surface of 11 mm. Further dimensions can be found in the picture gallery. How is it mounted? The striking plate is screwed to the wood at a 90 degree angle with 2 wood screws. The retaining bracket ensures a secure hold and is easy to fit. Scope of delivery1x Locking angle SW3 11mm

€2.99*
Locking angle SW9 9.5mm
Locking angle SW9 The locking bracket is an optimal accessory for wooden furniture cam locks, screw-on locks and espagnolette locks. The material is steel and the surface is nickel-plated. How is it mounted? The striking plate is screwed to the wood with 2 wood screws at a 90 degree angle. The mounting bracket is easy to fit and ensures a secure hold for the transom. Scope of delivery:1x Locking angle SW9  9.5mm

€2.49*
Locking angle SW5 9.5mm
Locking angle SW5 Counterpart for cam locks, for locking lockers, compartments and cabinets. Suitable for use with lever, furniture, code and sash locks. The striking plate is made of steel and the surface is nickel-plated.The angle offers a surface of 9.5 mm with which the bolt is held. Further dimensions can be found in the picture gallery. How is it mounted? The striking plate is screwed to the wood with 2 wood screws at a 90 degree angle. The mounting bracket is easy to fit and ensures a secure hold for the transom. Scope of delivery:1x Locking angle SW5 9.5mm

€2.49*
Locking angle SW2 12mm
Locking angle SW2  Counterpart for deadbolt locks, for locking lockers, compartments and cabinets. Suitable for use with lever, furniture, code and sash locks. The striking plate is made of steel and the surface is nickel-plated. The angle offers a surface of 12mm with which the bolt is held. Further dimensions can be found in the picture gallery.How is it mounted? The striking plate is screwed to the wood at a 90 degree angle with 2 wooden screws. The retaining bracket is easy to fit and ensures that the bolt is held securely. Scope of delivery: 1x locking angle SW2

€2.49*
Loading...
Upload in progress, please be patient ...